|
|
1.1 root 1: .\" Copyright (c) 1986 The Regents of the University of California.
2: .\" All rights reserved.
3: .\"
4: .\" Redistribution and use in source and binary forms are permitted provided
5: .\" that: (1) source distributions retain this entire copyright notice and
6: .\" comment, and (2) distributions including binaries display the following
7: .\" acknowledgement: ``This product includes software developed by the
8: .\" University of California, Berkeley and its contributors'' in the
9: .\" documentation or other materials provided with the distribution and in
10: .\" all advertising materials mentioning features or use of this software.
11: .\" Neither the name of the University nor the names of its contributors may
12: .\" be used to endorse or promote products derived from this software without
13: .\" specific prior written permission.
14: .\" THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED
15: .\" WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
16: .\" MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
17: .\"
18: .\" @(#)de.4 6.4 (Berkeley) 6/23/90
19: .\"
20: .TH DE 4 "June 23, 1990"
21: .UC 5
22: .SH NAME
23: de \- DEC DEUNA 10 Mb/s Ethernet interface
24: .SH SYNOPSIS
25: .B "device de0 at uba0 csr 174510 vector deintr"
26: .SH DESCRIPTION
27: The
28: .I de
29: interface provides access to a 10 Mb/s Ethernet network through
30: a Digital Equipment UNIBUS Network Adapter (DEUNA).
31: .PP
32: Each of the host's network addresses
33: is specified at boot time with an SIOCSIFADDR
34: ioctl. The
35: .I de
36: interface employs the address resolution protocol described in
37: .IR arp (4)
38: to dynamically map between Internet and Ethernet addresses on the local
39: network.
40: .PP
41: The interface normally tries to use a ``trailer'' encapsulation
42: to minimize copying data on input and output.
43: The use of trailers is negotiated with ARP.
44: This negotiation may be disabled, on a per-interface basis,
45: by setting the IFF_NOTRAILERS
46: flag with an SIOCSIFFLAGS ioctl.
47: .SH DIAGNOSTICS
48: \fBde%d: hardware address %s\fP.
49: This is a normal autoconfiguration message noting the 6 byte physical
50: ethernet address of the adapter.
51: .PP
52: \fBde%d: oerror, flags=%b tdrerr=%b (len=%d)\fP.
53: The hardware indicated an error
54: in transmitting a packet to the cable.
55: The status and error flags are reported.
56: .PP
57: \fBde%d: ierror, flags=%b lenerr=%b (len=%d)\fP.
58: The hardware indicated an error
59: in reading a packet from the cable.
60: The status and error flags are reported.
61: .PP
62: \fBde%d: can't handle af%d\fP. The interface was handed
63: a message with addresses formatted in an unsuitable address
64: family; the packet was dropped.
65: .PP
66: \fBde%d: buffer unavailable\fP. The interface received more packets
67: than it had buffers allocated to receive them.
68: .PP
69: \fBde%d: address change failed, csr0=%b csr1=%b\fP.
70: The interface was unable to reprogram
71: its physical ethernet address.
72: This may happen with very early models of the interface.
73: This facility is used only when
74: the controller is not the first network interface configured for XNS.
75: .PP
76: The following messages indicate a probable hardware error performing
77: the indicated operation during autoconfiguration or initialization.
78: The two control and status registers
79: should indicate the nature of the failure.
80: See the hardware manual for details.
81: .PP
82: \fBde%d: reset failed, csr0=%b csr1=%b\fP.
83: .PP
84: \fBde%d: ppcb failed, csr0=%b csr1=%b\fP.
85: .PP
86: \fBde%d: read addr failed, csr0=%b csr1=%b\fP.
87: .PP
88: \fBde%d: wtring failed, csr0=%b csr1=%b\fP.
89: .PP
90: \fBde%d: wtmode failed, csr0=%b csr1=%b\fP.
91: .SH SEE ALSO
92: netintro(4), inet(4), arp(4)
This archive runs on limited infrastructure. Preserving old code on modern bandwidth. Automated agents are requested to crawl responsibly.