Return to eth82586.h CVS log

Up to [GnuMach] / Gnu-Mach / linux / src / drivers / net

Annotation of Gnu-Mach/linux/src/drivers/net/eth82586.h, revision 1.1

1.1     ! root        1: /*
        !             2:  * eth82586.h: Intel EtherExpress defines
        !             3:  *
        !             4:  * Written 1995 by John Sullivan
        !             5:  * See eexpress.c for further details
        !             6:  * documentation and usage to do.
        !             7:  */
        !             8: 
        !             9: /*
        !            10:  * EtherExpress card register addresses
        !            11:  * as offsets from the base IO region (dev->base_addr)
        !            12:  */
        !            13: 
        !            14: #define DATAPORT 0x0000
        !            15: #define WRITE_PTR 0x0002
        !            16: #define READ_PTR 0x0004
        !            17: #define SIGNAL_CA 0x0006
        !            18: #define SET_IRQ 0x0007
        !            19: #define SM_PTR 0x0008
        !            20: #define MEM_Ctrl 0x000b
        !            21: #define MEM_Page_Ctrl 0x000c
        !            22: #define Config 0x000d
        !            23: #define EEPROM_Ctrl 0x000e
        !            24: #define ID_PORT 0x000f
        !            25: 
        !            26: /*
        !            27:  * offset to shadowed memory, 0 <= x <= 31. We don't use this yet,
        !            28:  * but may in the future. Is shadow memory access any faster than
        !            29:  * dataport access?
        !            30:  */
        !            31: #define SM_ADDR(x) (0x4000+((x&0x10)<<10)+(x&0xf))
        !            32: 
        !            33: /* Always mirrors eexp-memory at 0x0008-0x000f */
        !            34: #define SCB_STATUS 0xc008
        !            35: #define SCB_CMD 0xc00a
        !            36: #define SCB_CBL 0xc00c
        !            37: #define SCB_RFA 0xc00e
        !            38: 
        !            39: 
        !            40: 
        !            41: /*
        !            42:  * card register defines
        !            43:  */
        !            44: 
        !            45: /* SET_IRQ */
        !            46: #define SIRQ_en 0x08
        !            47: #define SIRQ_dis 0x00
        !            48: 
        !            49: /* Config */
        !            50: #define set_loopback outb(inb(ioaddr+Config)|0x02,ioaddr+Config)
        !            51: #define clear_loopback outb(inb(ioaddr+Config)&0xfd,ioaddr+Config)
        !            52: 
        !            53: /* EEPROM_Ctrl */
        !            54: #define EC_Clk 0x01
        !            55: #define EC_CS  0x02
        !            56: #define EC_Wr  0x04
        !            57: #define EC_Rd  0x08
        !            58: #define ASIC_RST 0x40
        !            59: #define i586_RST  0x80
        !            60: 
        !            61: #define eeprom_delay() { int _i = 40; while (--_i>0) { __SLOW_DOWN_IO; }}
        !            62: 
        !            63: /*
        !            64:  * i82586 Memory Configuration
        !            65:  */
        !            66: 
        !            67: /* (System Configuration Pointer) System start up block, read after 586_RST */
        !            68: #define SCP_START 0xfff6
        !            69: 
        !            70: 
        !            71: /* Intermediate System Configuration Pointer */
        !            72: #define ISCP_START 0x0000
        !            73: /* System Command Block */
        !            74: #define SCB_START 0x0008
        !            75: 
        !            76: /*
        !            77:  * Start of buffer region. If we have 64k memory, eexp_hw_probe() may raise
        !            78:  * NUM_TX_BUFS. RX_BUF_END is set to the end of memory, and all space between
        !            79:  * the transmit buffer region and end of memory used for as many receive buffers
        !            80:  * as we can fit. See eexp_hw_[(rx)(tx)]init().
        !            81:  */
        !            82: #define TX_BUF_START 0x0100
        !            83: #define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)
        !            84: #define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)
        !            85: 
        !            86: 
        !            87: 
        !            88: /*
        !            89:  * SCB defines
        !            90:  */
        !            91: 
        !            92: /* these functions take the SCB status word and test the relevant status bit */
        !            93: #define SCB_complete(s) ((s&0x8000)!=0)
        !            94: #define SCB_rxdframe(s) ((s&0x4000)!=0)
        !            95: #define SCB_CUdead(s) ((s&0x2000)!=0)
        !            96: #define SCB_RUdead(s) ((s&0x1000)!=0)
        !            97: #define SCB_ack(s) (s & 0xf000)
        !            98: 
        !            99: /* Command unit status: 0=idle, 1=suspended, 2=active */
        !           100: #define SCB_CUstat(s) ((s&0x0300)>>8)
        !           101: 
        !           102: /* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
        !           103: #define SCB_RUstat(s) ((s&0x0070)>>4)
        !           104: 
        !           105: /* SCB commands */
        !           106: #define SCB_CUnop     0x0000
        !           107: #define SCB_CUstart   0x0100
        !           108: #define SCB_CUresume  0x0200
        !           109: #define SCB_CUsuspend 0x0300
        !           110: #define SCB_CUabort   0x0400
        !           111: 
        !           112: /* ? */
        !           113: #define SCB_resetchip 0x0080
        !           114: 
        !           115: #define SCB_RUnop     0x0000
        !           116: #define SCB_RUstart   0x0010
        !           117: #define SCB_RUresume  0x0020
        !           118: #define SCB_RUsuspend 0x0030
        !           119: #define SCB_RUabort   0x0040
        !           120: 
        !           121: 
        !           122: /*
        !           123:  * Command block defines
        !           124:  */
        !           125: 
        !           126: #define Stat_Done(s)   ((s&0x8000)!=0)
        !           127: #define Stat_Busy(s)   ((s&0x4000)!=0)
        !           128: #define Stat_OK(s)     ((s&0x2000)!=0)
        !           129: #define Stat_Abort(s)  ((s&0x1000)!=0)
        !           130: #define Stat_STFail    ((s&0x0800)!=0)
        !           131: #define Stat_TNoCar(s) ((s&0x0400)!=0)
        !           132: #define Stat_TNoCTS(s) ((s&0x0200)!=0)
        !           133: #define Stat_TNoDMA(s) ((s&0x0100)!=0)
        !           134: #define Stat_TDefer(s) ((s&0x0080)!=0)
        !           135: #define Stat_TColl(s)  ((s&0x0040)!=0)
        !           136: #define Stat_TXColl(s) ((s&0x0020)!=0)
        !           137: #define Stat_NoColl(s) (s&0x000f)
        !           138: 
        !           139: /* Cmd_END will end AFTER the command if this is the first
        !           140:  * command block after an SCB_CUstart, but BEFORE the command
        !           141:  * for all subsequent commands. Best strategy is to place
        !           142:  * Cmd_INT on the last command in the sequence, followed by a
        !           143:  * dummy Cmd_Nop with Cmd_END after this.
        !           144:  */
        !           145: #define Cmd_END     0x8000
        !           146: #define Cmd_SUS     0x4000
        !           147: #define Cmd_INT     0x2000
        !           148: 
        !           149: #define Cmd_Nop     0x0000
        !           150: #define Cmd_SetAddr 0x0001
        !           151: #define Cmd_Config  0x0002
        !           152: #define Cmd_MCast   0x0003
        !           153: #define Cmd_Xmit    0x0004
        !           154: #define Cmd_TDR     0x0005
        !           155: #define Cmd_Dump    0x0006
        !           156: #define Cmd_Diag    0x0007
        !           157: 
        !           158: 
        !           159: /*
        !           160:  * Frame Descriptor (Receive block) defines
        !           161:  */
        !           162: 
        !           163: #define FD_Done(s)  ((s&0x8000)!=0)
        !           164: #define FD_Busy(s)  ((s&0x4000)!=0)
        !           165: #define FD_OK(s)    ((s&0x2000)!=0)
        !           166: 
        !           167: #define FD_CRC(s)   ((s&0x0800)!=0)
        !           168: #define FD_Align(s) ((s&0x0400)!=0)
        !           169: #define FD_Resrc(s) ((s&0x0200)!=0)
        !           170: #define FD_DMA(s)   ((s&0x0100)!=0)
        !           171: #define FD_Short(s) ((s&0x0080)!=0)
        !           172: #define FD_NoEOF(s) ((s&0x0040)!=0)

This archive runs on limited infrastructure. Preserving old code on modern bandwidth. Automated agents are requested to crawl responsibly.