Return to SUN2-MULTIBUS CVS log

Up to [The Machine Emulator] / tme / machine / sun2

tme-0.4

# $Id: SUN2-MULTIBUS,v 1.1.1.3 2018/04/24 16:40:09 root Exp $

## SUN2-MULTIBUS - example tmesh commands to create a Sun2 Multibus
## machine:

## the Multibus and VME sun2 common buses and devices:
##
mainbus0: tme/machine/sun2 multibus my-sun2-idprom.bin
cpu0 at mainbus0: tme/ic/m68010
obio0 at mainbus0 obio: tme/generic/bus size 8MB
obmem0 at mainbus0 obmem: tme/generic/bus size 16MB
ram0 at obmem0 addr 0x0: tme/host/posix/memory ram 4MB
rom0 at obmem0 addr 0xef0000: tme/host/posix/memory rom sun2-multi-rev-R.bin
rom0 at obmem0 addr 0xef8000

## the Multibus sun2 obio devices:
##
clock0 at obio0 addr 0x2800: tme/machine/sun2/clock
tod0 at obio0 addr 0x3800: tme/machine/sun2/tod
zs0 at obio0 addr 0x2000 ipl 6: tme/machine/sun2/zs

## the Multibus sun2 Multibus buses:
##
mbio0 at mainbus0 mbio: tme/generic/bus size 8MB
mbmem0: tme/generic/bus size 8MB
mainbus0 mbmem at mbmem0 addr 0x00000

## the Sun "SCSI-2" Multibus board:
##
sc0 at mbmem0 addr 0x80000 ipl 2: tme/bus/multibus/sun-sc
scsibus0 at sc0: tme/scsi/bus
#zs2 at mbmem0 addr 0x80800 ipl 6: tme/machine/sun2/zs
#zs3 at mbmem0 addr 0x81000 ipl 6: tme/machine/sun2/zs

## the 3Com 3C400 Ethernet Multibus board:
##
# uncomment these two lines if you have read/write permission on one
# of your /dev/bpfN devices and you want an Ethernet device:
#
#ec0 at mbmem0 addr 0xe0000 ipl 3: tme/bus/multibus/3c400 ether "00:01:02:03:04:05"
#bpf0 at ec0: tme/host/bsd/bpf

## the Sun Intel Ethernet Multibus board:
##
## NB that the mie "memory" attachment argument must match the
## low 20 bits of the address of the memory's bus attachment:
##
# uncomment these lines if you have read/write permission on one
# of your /dev/bpfN devices and you want an Ethernet device:
#
#mie0: tme/bus/multibus/sun-mie
#mie0 csr at mbmem0 addr 0x88000 ipl 3
#mie0 memory 0xa0000 at mbmem0 addr 0xa0000
#ie0 at mie0: tme/ic/i82586
#bpf1 at ie0: tme/host/bsd/bpf delay 10000

## the Sun bwtwo Multibus board, Sun type-2 keyboard and mouse, and
## the GTK-based display to drive them all:
##
# comment out these eight lines if you don't have GTK or you don't
# want a display console:
#
bwtwo0 at obmem0 addr 0x700000 ipl 4: tme/machine/sun2/bwtwo type multibus
zs1 at obmem0 addr 0x780000 ipl 6: tme/machine/sun2/zs
kbd0 at zs1 channel A: tme/serial/keyboard type sun-type-2 macros my-sun-macros.txt map sun-keyboards.txt rate 20
ms0 at zs1 channel B: tme/serial/mouse type mousesystems-5
display0: tme/host/gtk/display
display0 at bwtwo0
display0 at kbd0
display0 at ms0

## ttya:
##
# uncomment the following line if you aren't using the GTK-based
# display console above.  this will connect ttya to the master side of
# a pseudo-tty (in this case, /dev/ttyr0), which you can connect to
# using tip or some other serial communications program on the slave
# side (in this case, /dev/ptyr0):
#
#console0 at zs0 channel A: tme/host/posix/serial device /dev/ttyr0 break-carats

## a SCSI disk:
##
# if you're using SunOS, change the disk type from tme-scsi-1 to
# acb4000, to get an Adaptec ACB-4000 compatible disk:
#
sd0 at scsibus0: tme/scsi/disk id 0 type tme-scsi-1
disk0 at sd0: tme/host/posix/disk file my-sun2-disk.img

## a SCSI tape:
##
# if you're using SunOS, remove the vendor EMULEX and product "MT-02 QIC" 
# to get a 100% Emulex MT-02 compatible tape:
#
st0 at scsibus0: tme/scsi/tape id 4 type emulex-mt02 vendor EMULEX product "MT-02 QIC"
tape0 at st0: tme/host/posix/tape

## power up the machine:
##
# uncomment this line to automatically power up the machine when
# tmesh starts:
#
# command mainbus0 power up

This archive runs on limited infrastructure. Preserving old code on modern bandwidth. Automated agents are requested to crawl responsibly.